indentor的意思、解釋

名詞委托代購商，訂貨商

1. 壓痕囂,壓痕物：壓痕試驗indentation test | 壓痕囂,壓痕物indentor | 壓痕硬度試驗機indentation hardness tester

2. 壓痕計：Hydraulic Saw油壓鋸臺[設備] | Indentor壓痕計 | Injection Molding射出成型

3. 壓痕器：壓痕鋼珠 indenting ball | 壓痕器 indentor | 單獨司軔閥 independent brake valve

4.

4. 委托代購商：委托辯護 instruction to defend | 委托代購商 indentor | 委托人 principal,entruster

1. Indentor shape was not a significant factor on failure load or failure strength.

壓物的形狀在負荷失敗率和強度失敗率中不是主要因素。

2. indentor的翻譯

2. Charles E. Smith, to conduct a business in chemicals, cement, paper, milk-products, etc., as importers and indentor.

E。史密斯先生在1947年創立的，其主要業務為藥品、水泥、紙張及乳制品等貨物的進口與購

3. Indentor and the applied force influence the measurements such that no simple relationship exists between the measure-ments obtained with one type of durometer and those obtained with another type of durometer or other instruments used for measuring hardness.

壓足的幾何形狀和施加力對測量的結果有影響，不同類型的硬度計和測量儀器測出的硬度值之間的不存在簡單的關系。

4. In this method, drilling the double holes in the two sides of the point to be determined in welded joints, load material bridge by an indentor until it is broken, record the response between applied load and indentor displacement.

在被測材料的小區域兩側開兩小孔，剪切刀具從其中一孔對被測區域的材料加載直到破壞，記錄加載過程中的載荷位移曲線。

5. 1 This test method is based on the penetration of a specific type of indentor when forced into the material under specified conditions. The indentation hardness is inversely related to the penetration and is dependent on the elastic modulus and viscoelastic behavior of the material. The geometry of the

4.1本測試方法是根據有關規定，將指定類型的壓足壓入測試材料進行測量的，反言之，硬度與壓入量有關，同時又與材料的彈性模量和粘彈性能有關。

6. indentor

6. In this method, drill the double holes in the two sides of the point to be determined in welded joints, load material bridge by an indentor until it is broken, record the response between applied load and indentor displacement. We can call this method as double holes microshear test.

在被測材料的小區域兩側開兩小孔，剪切刀具從其中一孔對被測區域的材料加載直到破壞，記錄加載過程中的載荷位移曲線。

7. indentor

7. Methods. An elliptical or a cloverleaf-shaped indentor covering 40% of the endplate was axially compressed against the superior endplate of 48 thoracolumbar vertebrae.

在48塊胸腰椎椎體中，選用橢圓形或者四葉狀的鋸齒邊緣的壓力器，接觸椎體的面積約為40％的終板面積，作軸向壓迫。

8. Based on the above straight lines, the contact zone can be determined from the known indentor curvature and loading.

根據這些直線族，可以由已知的壓頭曲率和外載荷確定接觸區尺寸。

9. The fracture toughness KIC of TiAlN coating has been measured by Weishi indenter indentor and the appearance of impress has also been observed by SEM.

并采用維氏壓頭測量斷裂韌性KIC和通過掃描電子顯微鏡觀察壓痕形貌來評定涂層的韌性。